JD-148 is a two-component solvent-free anti-corrosion epoxy floor paint. Nice appearance, dust &corrosion resistant and easy to clean. The whole coating system can bond well with the solid base and has good abrasion and wearing resistance. Meanwhile, it is resistant to compression and impact and can stand heavy-duty load to a certain extent.
1. Seamless, dust-proof and easy to clean 2. Solvent-free and environmental 3. Dense corrosion-resistance surface 4. Bright &smooth surface
Where to Use:
It is mainly used for concrete surface where has compression & wearing resistance and anti-dust and corrosion requirement, such as industry workshop, office, warehouse, foodstuff factory etc.
Configuration of Coating System:
Requirements for the base:
1. Concrete strength≥C25; 2. Flatness: the maximum altitude difference of 2M running rule<3mm.
3. The moisture content of the base<4%
Touch dry: 2 hours Hard dry: 1 day
Compressive strength (Mpa):
Impact resistance strength (Kg·cm):
Flexural strength (Mpa):
Adhesive force grade:
Hardness (Shore D):
Abrasion resistance(750g/1000r, zero gravity, g)
Resistance to engine oil, diesel oil for 60 days:
Resistance to 50% sulfuric acid for 20 days:
Resistance to 25% Sodium hydroxide for 30 days:
Resistance to toluene, ethanol for 60 days:
Primer: 0.15kg/sqm Undercoat: 0.5kg/sqm Quartz Powder: 0.25kg/sqm Top coat: 0.3kg/sqm
1. Surface preparation:Correct substrate preparation is critical for optimum performance. Surface should be sound, clean, dry and free from loose particles, oil, grease, and other contaminants.
2. Primer: Prepare a barrel, pour JD-D10A and JD-D10B in it based on 1:1. Stir the mixture well and then apply it with roller or trowel. The reference consumption is 0.15kg/m².The main purpose of this primer is to seal the substrate completely and avoid air-bubbles in the body coat. A second coat may be required depending on the oil absorption condition of substrate. The recoat time is about 8 hours.
Inspection standard for the primer: even film with certain brightness. 3.Undercoat: Mix WTP-MA and WTP-MB based on 5:1 first, then add quartz powder (1/2 of the mixture of A and B) into the mixture, stir it well and apply with trowel. The consumption quantity of A and B is 0.5kg /sqm. You can do it one coat at one time or two coats at two times. In the second case, the application interval is about 8 hours at 25 degrees. Sand the first layer, clean it and then apply the second layer. After the whole application, wait another 8 hours, grind it, clean the sanding dust and then continue the next procedure.
Inspection standard for the undercoat: Non-sticky to hand, no softening, no nail print if you scratch the surface.
4.Top coat: Mix JD-148 A and JD-148 B based on 5:1 and then apply the mixture with roller. The consumption quantity is 0.3kg/sqm.
5.Maintenance: 5-7 days. Don’t put the floor into use or wash it with water or other chemicals.
Clean the application tools first with paper towels, then clean the tools with solvent before the paint hardens
Health and safety information
It contains certain chemicals which can cause skin irritation. Wear gloves, masks while handling the product, washing thoroughly after handling. Should skin contact occur, wash immediately with soap and water. During application and curing in closed rooms, adequate fresh air ventilation must be provided. Keep away from open flames including welding.
In case of accidental eye contact, wash with a large quantity of water and immediately seek medical advice. For detailed health, safety, environment recommendations, please consult and follow the instruction on the product material safety data sheet.
The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further written enquiries as to the suitability for the intended purpose does so at his own risk and we can accept no liability of the product for any loss or damage arising out of such use. Product data are subject to change without notice and become void five years from the date of issue.
The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since we cannot anticipate or control many conditions under which our products may be used, we can only guarantee the quality of the product itself. We reserve the right to alter the given information without prior notice.
Packaging & Shipping
Primer: A:18kg/tin B:18kg/tin
Under coat: A:25kg/tin B:5kg/tin
Top coat: A:25kg/tin B:5kg/tin
Shipping Date: 7 days after confirmed order
Guangdong Maydos Building Materials Co.,Ltd, founded in 1995, is located in Shunde district,Foshan, Guangdong province , it now becomes one of the top 10 chemical enterprises in China. Maydos is mainly specialized in manufacture of high quality Architectural Building Paint,Floor Paint, Wood Lacquer,Industrial Anti-Rust Paint, Road Paint,Chloroprene Rubber Adhesive, SBS Adhesive, PU Adhesive, Emulsion Glue.
So far, Maydos has won many honors for its products. Such as ISO14025 Ecolabelling certificate, ISO9001 and ISO14001 certificate and the certificate for product exempt from quality surveillance inspection. Based on company's robust development and great success in domestic market, Maydos launched its international business at the end of 2005. So far as it is concerned, it has exported its products to over 60 countries in Europe, Asia, Africa, Oceania and America and Maydos Brand is well accepted by the consumers of the local market.
1)24 hours technical support by e-mail.
2)OEM.We can provide customized service.
3)one year guarantee for whole machine except of laser tube and lens.